9 Simple Steps to Waterproofing Exterior Walls
“The foundation of your home is built on the walls. The weather out there will not be nice and you need to pay special attention to the exterior walls of your house. It’s not enough to paint a wall. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will start peeling off regardless of how expensive it is.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
“The outer part of your home’s wall is usually covered with a lot of dust and dirt from the outside. To ensure the efficiency of the whole process, you need to clear off the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. Then use a power washer to finish it all off.”
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop over time. Follow up the cleaning process with a thorough finding of all the cracks and holes on the wall to ensure proper weatherproofing. Just fill them with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
The mixture of cement penetrated inside the cracks. Make sure you remove the loose cement from the wall before applying the cement.
Step 4: Add a layer of cement waterproofing sealer
To make sure your wall is waterproof, you need to apply a cement waterproofer. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal. Allow it to become dry.
Step 5: Pick the right water-proofer
There are a lot of waterproof products available in the market. You need to choose the right one for your wall. The water-proofer should be selected based on whether the wall is concrete or silicate.
A silicate-based concrete sealer is one of the options you can choose from. Pick a plaster waterproof Additive that will add strength to your waterproofed walls.
Step 6: Apply the water-proofer
Apply the water-proofer thoroughly on the walls with a roller or brush. If you want to apply more than one coat, give a thin coat first. Allow the first coating to dry before adding the second one.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layers, you need to use a tar-based pitch after the drying of the cement waterproofer. On the exterior wall, apply it.
After that, you need to apply a heavy-duty plastic or rubber membrane for waterproofing, which will ensure the proper care of your walls.
Step 8: Consider adding gravel
A proper base for the trench is below the footer. The drainage pipes will get adequate support from a gravel base. Gravel is long-lived and provides enhanced protection.
You need to lay the drainage pipe-cover and gravel. The gravel should be level near the footer. Make sure the pipe is covered for at least 3 inches.
Step 9: Add a fabric barrier
Attach the fabric barrier to the pipe. Ensuring a fabric barrier is going to prevent the formation of dirt and keep your system running. Simply back-fill the trench and build the top of the dirt relatively high and allow it to settle for a while. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia,Trademarkia
Good waterproof gives your home a new life and strength to deal with outside weather issues. If you want good solutions for your walls, Magicrete is here to help you. At a very low and affordable price, Magicrete offers proper weatherproofing.
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it”